|
|
Deep Rectangle Bath Bar Soap Mold (MW 519) |
|
|
|
 |
Additional
Information |
|
Directions &
Ingredients |
|
SDS &
Documents |
|
|
Common Uses:
Melt & Pour Soap. Cold Process Soap. Lotion Bars.
Points of Interest:
Milky Way® Molds are constructed of plastic and have angled sides for easier soap removal. The dimensions listed are for the largest sides. The bottom of each cavity will be slightly smaller than the dimensions listed.
Manufacturer: Milky Way Molds
Material: Clear PVC (Not Approved for Food Contact)
Country of Origin: United States
Milky Way Soap Molds can tolerate temperatures of 135-145 degrees F. Above these temperatures, warping may occur. Soap is easiest to release 12-24 hours after cooling.
Wash molds in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
Country Of Origin: United States
|
Directions:
Melt & Pour Soap: Pour melted soap at a temperature no hotter than 135ºF into mold. Cool until soap has hardened. Remove soap from mold. For easier unmolding, place into freezer for 30 minutes, and then immerse bottom of the mold in hot water for a few moments. Do not use cooking spray to coat mold.
Cold Process Soap: Coat the mold with cooking spray. Pour soap at trace into mold. After 24 hours, flip mold over onto a clean surface. Gently push the back of the mold until the soap begins to release then pull the soap out of the mold with a gloved hand. Allow soap to cure for 4-8 weeks. Note that some CP soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Lotion Bars: Pour melted lotion bar mixture into mold cavities at a temperature no hotter than 135ºF. Allow mixture to solidify. Flip mold over onto clean surface. Gently push back of mold until lotion bar begins to release then pull bar out of mold.
Care:
Wash in warm, sudsy water. Please avoid the dishwasher because that can warp your molds or make them brittle.
| Average Customer Rating: |
 |
(4 Reviews) |
|
MaReesa • Washington
Date Submitted: 10/22/2019
I Recommend This Product!
|
 |
"Good size & shape" |
|
COMMENTS: I like the size and shape of this mold. It makes a nice looking bar that fits in your hand. More interesting than a basic rectangle. It was a little hard to unmold the soap afterwards, but I managed. The trick is not to fill up the cavity all the way to the top - that way you can use your finger to push the side away from the soap. Once you break the air seal on the sides, you can flip it over and push from the bottom to get the soap to release.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• size
• shape
|
|
• a little hard to unmold
|
|
|
|
Brenda • Missouri
Date Submitted: 09/04/2018
|
 |
"Not bad" |
|
COMMENTS: I'm happy as far as getting the size/shape bar I was hoping for. I do feel like the mold is kind of pricy for what you get, and I have a VERY hard time getting the soaps out of the mold.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Size of the mold
|
|
• Price
• Flexibility of the mold
|
|
|
|
Jamie • Arizona
Date Submitted: 11/24/2017
I Recommend This Product!
|
|
"Rectangle Bath Bar Soap Mold (MW 519)" |
|
COMMENTS: My new favorite soap mold. I am glad I purchased 6 of these and now will be getting more soon. Use for both CP and MP. I leave MP in mold for 24 hours before popping them out, gentle pressure and the seal starts to unlock and out they come. CP I leave in for 72 hours and use sodium lactate in the soap batter and no issues getting them out there either but it may vary on your soap recipe. Nice, comfortable fit in hand. No more soap cutters for me yay!
|
|
PRODUCT USED IN: Soap - Melt & Pour, Soap - Cold Process
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Size
• Shape
• Simplicity
|
|
• A 4 cavity would be nice
|
|
|
|
Tina • Oregon
Date Submitted: 09/30/2017
|
|
"Bar soap mold (MW 519)" |
|
COMMENTS: Makes a nice full sized bar for my uses. Soap shape feels good in hand. A hard rigid clear plastic mold, somewhat difficult to unmold, perhaps due to the depth of the bars (which I like). The clear plastic makes it easy to see through what is going on inside as you are trying new techniques.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Produces shiny smooth bars
• I can see through the mold
• Comfortable size bar
|
|
|
|
|
| Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
 |
4 Question(s) Shown Below |
| Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|
