|
|
Ribbon Column Silicone Soap Mold 2029 |
The requested content cannot be found 1 / 2 Ribbon Column Silicone Soap Mold 2029
|
|
 |
Additional
Information |
|
Directions &
Ingredients |
|
SDS &
Documents |
|
|
Make ribbon shaped soaps to show your support to a cause! Embed the ribbon into a loaf to create soaps that raise awareness. Use the Teardrop Column Mold to create the middle of the ribbon (sold separately). Embed fits in Crafter's Choice Regular Loaf Silicone Mold 1501 and Rectangle Regular Column Silicone Soap Mold 2009.
Common Uses:
Melt & Pour Soap. Cold Process Soap.
Points of Interest:
Manufacturer: Crafter's Choice
Material: Silicone
Country of Origin: China
NOTE: To minimize bowing pour soap in layers.
Country Of Origin: China
|  | This product is not on the CA Prop 65 list of toxic chemicals.
This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
|
|
International Nomenclature of Cosmetic Ingredients (INCI):
This product does need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved):
This product does need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Close the mold by firmly pressing the edges together. For added safety, clamp the edges. Slowly pour melted soap no hotter than 130ºF into mold. Allow soap to harden then open mold and remove soap. Trim edges with a potato peeler or spatula. Embed soap into a loaf or slice into bars.
Cold Process Soap: Close the mold by firmly pressing the edges together, and clamp the edges. Slowly pour traced soap into mold. After at least 24 hours, open mold and remove soap with gloved hands. Trim edges with a potato peeler or spatula. Embed soap into a loaf or slice into bars. Allow soap to cure for 4-8 weeks. Note that some cp soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Care:
Hand wash mold in warm, sudsy water.
| Average Customer Rating: |
 |
(1 Reviews) |
|
Brigid • Pennsylvania
Date Submitted: 11/26/2020
|
|
"Huge disappointment " |
|
COMMENTS: I have been using column molds for years with my CP soap. I was so excited when I saw these... Then I used them.. They look okay in the end, but they leak like crazy, even with binder clips up both sides, they are only 8" long, which means I have to make 3 for it to fit my 18" mold, and they are almost impossible to get the soap out of without breaking. At $22 a mold (which is much more expensive than the 12" column molds I normally use), I expected much better. Total waste of $45.
|
|
PRODUCT USED IN: Soap - Cold Process
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
|
|
• Leaks
• Length
|
|
|
| Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
 |
4 Question(s) Shown Below |
| Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|
