|
|
 |
Additional
Information |
|
Directions &
Ingredients |
|
SDS &
Documents |
|
|
Create a beautiful bar with this Wave Silicone Mold. The mold has four rectangle bar cavities with a unique wave design that allow you to easily make a bar of soap that everyone will love.
Country Of Origin: China
|
International Nomenclature of Cosmetic Ingredients (INCI):
This product does need to be listed on the product ingredient label.
Common Name Ingredient Listing (FDA Approved):
This product does need to be listed on the product ingredient label.
Directions:
Melt & Pour Soap: Pour melted soap into silicone mold cavities. Allow soap to cool at room temperature until hard. Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold.
Cold Process Soap: Pour soap at trace into the mold cavities. After at least 24 hours, gently pull silicone mold to loosen its grip on the soap. Flip mold over onto a clean surface and gently push on the bottom of mold until the soap starts to release. Grab hold of the soap with a gloved hand, and allow soap to cure for 4-8 weeks. Note that some cold process soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Cold Process/Oven Process Soap: Pour soap at trace into the mold cavities. Preheat oven to 170ºF then place mold in oven. Turn oven off, and keep soap in oven overnight. The next day remove mold from oven. Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold. Allow soap to cure for 2 to 4 weeks.
Hot Process Soap: Scoop hot process soap into mold cavities. Gently tap the mold onto the counter to remove air pockets. Allow soap to cool and harden. (This can take up to 48 hours.) Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold.
Lotion Bars: Pour melted lotion bar mixture into mold cavities. Allow mixture to solidify. Carefully remove lotion bars from mold by gently pulling the sides away from the lotion bars, and then push on the bottom of the mold until the lotion bars starts to release. Grab hold of lotion bar and carefully pull out of mold.
Care:
Hand wash in warm sudsy water.
| Average Customer Rating: |
 |
(2 Reviews) |
|
Oliver • California
Date Submitted: 04/10/2023
I Recommend This Product!
|
|
"Perfect with Mica" |
|
COMMENTS: I use these for my melt & pour soaps. It makes a beautiful shape, but you can really make it pop by painting it with some shimmering mica. I have an activated charcoal bar I use gold mica on and the effect is fantastic. Comes out of the molds very easy to and is easy to clean.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Shape
• Size
• Ease of Use
|
|
|
|
|
|
Becki • Michigan
Date Submitted: 11/29/2022
I Recommend This Product!
|
|
"My First Silicone Mold and I'm Back to Buy More!" |
|
COMMENTS: I've made M&P soap for years, just for personal use and as gifts. I only ever used the plastic, hard molds because they're cheaper & come in so many different patterns/shapes. It sometimes would take a little time to get the soap out of the plastic molds (especially if there was a mold in the center!) but eventually it'd pop out.
But, the last few times I made soap, due to my arthritic fingers (I have both Rheumatoid and severe Osteo arthritis), I struggled to get any of the soaps to pop out. I finally ended up asking my husband (who, of course, managed with no problem), but I ordered this mold the very next day.
Today, I used it for the first time and YAY, I had no issues at all - the bars are bigger than I thought they'd be and the pattern, even in just a solid color with no special touches, is striking. I'm now cruising for another silicone mold to purchase today.
|
|
PRODUCT USED IN: Soap - Melt & Pour
|
| THINGS I LIKE |
|
THINGS I'D LIKE TO CHANGE |
• Pleasing, detailed pattern
• Larger bar size
• Ease of use
|
|
• Absolutely nothing
|
|
|
| Question + Answer. Here you can ask or answer questions All questions are queued and answered quickly during business hrs. You can also answer questions posted by other customers if you have valuable information. |
 |
1 Question(s) Shown Below |
| Distributor & Drop Shipper Minimum Advertised Pricing |
As a Crafter’s Choice Distributor and/or Drop Shipper you have agreed to abide by the following Minimum Advertised Price (MAP) for each product and price level. You are permitted to advertise products at a higher price. You may not advertise the products at a lower price. Below you will find the MAP for this product.
|
|
|
|
|
